/**
  ******************************************************************************
  * @file    main_lwip.h
  * @author  MCD Application Team
  * @version V1.1.0
  * @date    31-July-2013
  * @brief   This file contains all the functions prototypes for the main.c
  *          file.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT 2013 STMicroelectronics</center></h2>
  *
  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        http://www.st.com/software_license_agreement_liberty_v2
  *
  * Unless required by applicable law or agreed to in writing, software
  * distributed under the License is distributed on an "AS IS" BASIS,
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *
  ******************************************************************************
  */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __MAIN_LWIP_H
#define __MAIN_LWIP_H

#ifdef __cplusplus
 extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx.h"
#include "stm32f4x7_eth_bsp.h"

/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/

//#define USE_LCD        /* enable LCD  */
//#define USE_DHCP       /* enable DHCP, if disabled static address is used */

/* Uncomment SERIAL_DEBUG to enables retarget of printf to serial port (COM1 on STM32 evalboard)
   for debug purpose */
//#define SERIAL_DEBUG


/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
#define MAC_ADDR0   2
#define MAC_ADDR1   0
#define MAC_ADDR2   0
#define MAC_ADDR3   0
#define MAC_ADDR4   0
#define MAC_ADDR5   0

/*Static IP ADDRESS: IP_ADDR0.IP_ADDR1.IP_ADDR2.IP_ADDR3 */
#if 0
	/* IPµØÖ· */
	#define IP_ADDR0   g_tParam.lwip_ip[0]
	#define IP_ADDR1   g_tParam.lwip_ip[1]
	#define IP_ADDR2   g_tParam.lwip_ip[2]
	#define IP_ADDR3   g_tParam.lwip_ip[3]
	   
	/*NETMASK*/
	#define NETMASK_ADDR0   g_tParam.lwip_net_mask[0]
	#define NETMASK_ADDR1   g_tParam.lwip_net_mask[1]
	#define NETMASK_ADDR2   g_tParam.lwip_net_mask[2]
	#define NETMASK_ADDR3   g_tParam.lwip_net_mask[3]

	/*Gateway Address*/
	#define GW_ADDR0   g_tParam.lwip_gateway[0]
	#define GW_ADDR1   g_tParam.lwip_gateway[1]
	#define GW_ADDR2   g_tParam.lwip_gateway[2]
	#define GW_ADDR3   g_tParam.lwip_gateway[3]
#else
	#define IP_ADDR0   192
	#define IP_ADDR1   168
	#define IP_ADDR2   0
	#define IP_ADDR3   12
	   
	/*NETMASK*/
	#define NETMASK_ADDR0   255
	#define NETMASK_ADDR1   255
	#define NETMASK_ADDR2   255
	#define NETMASK_ADDR3   0

	/*Gateway Address*/
	#define GW_ADDR0   192
	#define GW_ADDR1   168
	#define GW_ADDR2   0
	#define GW_ADDR3   1
#endif

/* MII and RMII mode selection, for STM324xG-EVAL Board(MB786) RevB ***********/
//#define RMII_MODE  // User have to provide the 50 MHz clock by soldering a 50 MHz
                     // oscillator (ref SM7745HEV-50.0M or equivalent) on the U3
                     // footprint located under CN3 and also removing jumper on JP5.
                     // This oscillator is not provided with the board.
                     // For more details, please refer to STM3240G-EVAL evaluation
                     // board User manual (UM1461).


#define MII_MODE

/* Uncomment the define below to clock the PHY from external 25MHz crystal (only for MII mode) */
#ifdef 	MII_MODE
 #define PHY_CLOCK_MCO
#endif

/* STM324xG-EVAL jumpers setting
    +==========================================================================================+
    +  Jumper |       MII mode configuration            |      RMII mode configuration         +
    +==========================================================================================+
    +  JP5    | 2-3 provide 25MHz clock by MCO(PA8)     |  Not fitted                          +
    +         | 1-2 provide 25MHz clock by ext. Crystal |                                      +
    + -----------------------------------------------------------------------------------------+
    +  JP6    |          2-3                            |  1-2                                 +
    + -----------------------------------------------------------------------------------------+
    +  JP8    |          Open                           |  Close                               +
    +==========================================================================================+
  */

/* Exported macro ------------------------------------------------------------*/
/* Exported functions ------------------------------------------------------- */
void Time_Update(void);
void Delay(uint32_t nCount);


#ifdef __cplusplus
}
#endif

#endif /* __MAIN_H */


/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/