/**
 ******************************************************************************
 * @file    stm32f4x7_eth_conf.h
 * @author  MCD Application Team
 * @version V1.1.0
 * @date    31-July-2013
 * @brief   Configuration file for the STM32F4x7 Ethernet driver.
 ******************************************************************************
 * @attention
 *
 * <h2><center>&copy; COPYRIGHT 2013 STMicroelectronics</center></h2>
 *
 * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
 * You may not use this file except in compliance with the License.
 * You may obtain a copy of the License at:
 *
 *        http://www.st.com/software_license_agreement_liberty_v2
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 *
 ******************************************************************************
 */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F4x7_ETH_CONF_H
#define __STM32F4x7_ETH_CONF_H

#ifdef __cplusplus
extern "C"
{
#endif

/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx.h"

/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/

/* Uncomment the line below when using time stamping and/or IPv4 checksum offload */
#define USE_ENHANCED_DMA_DESCRIPTORS

    /* Uncomment the line below if you want to use user defined Delay function
       (for precise timing), otherwise default _eth_delay_ function defined within
       the Ethernet driver is used (less precise timing) */

#ifdef USE_Delay
    //  #include "main.h"              /* Header file where the Delay function prototype is exported */
#define _eth_delay_ ETH_Delay10ms /* User can provide more timing precise _eth_delay_ function \
                            in this example Systick is configured with an interrupt every 10 ms*/
    extern void ETH_Delay10ms(uint32_t nCount);
#else
#define _eth_delay_ ETH_Delay /* Default _eth_delay_ function with less precise timing */
#endif

/*This define allow to customize configuration of the Ethernet driver buffers */
#define CUSTOM_DRIVER_BUFFERS_CONFIG

#ifdef CUSTOM_DRIVER_BUFFERS_CONFIG
    /* Redefinition of the Ethernet driver buffers size and count */
#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
#define ETH_RXBUFNB     4                   /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
#define ETH_TXBUFNB     4                   /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
#endif

/* PHY configuration section **************************************************/
#ifdef USE_Delay
/* PHY Reset delay */
#define PHY_RESET_DELAY ((uint32_t)0x000000FF)
/* PHY Configuration delay */
#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF)
/* Delay when writing to Ethernet registers*/
#define ETH_REG_WRITE_DELAY ((uint32_t)0x00000001)
#else
/* PHY Reset delay */
#define PHY_RESET_DELAY     ((uint32_t)0x000FFFFF)
/* PHY Configuration delay */
#define PHY_CONFIG_DELAY    ((uint32_t)0x00FFFFFF)
/* Delay when writing to Ethernet registers*/
#define ETH_REG_WRITE_DELAY ((uint32_t)0x0000FFFF)
#endif

/*******************  PHY Extended Registers section : ************************/

/* These values are relatives to DP83848 PHY and change from PHY to another,
   so the user have to update this value depending on the used external PHY */

/* The DP83848 PHY status register  */
#define PHY_SR            ((uint16_t)0x10)   /* PHY status register Offset */
#define PHY_SPEED_STATUS  ((uint16_t)0x0002) /* PHY Speed mask */
#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /* PHY Duplex mask */

/* The DP83848 PHY: MII Interrupt Control Register  */
#define PHY_MICR        ((uint16_t)0x11)   /* MII Interrupt Control Register */
#define PHY_MICR_INT_EN ((uint16_t)0x0002) /* PHY Enable interrupts */
#define PHY_MICR_INT_OE ((uint16_t)0x0001) /* PHY Enable output interrupt events */

/* The DP83848 PHY: MII Interrupt Status and Misc. Control Register */
#define PHY_MISR             ((uint16_t)0x12)   /* MII Interrupt Status and Misc. Control Register */
#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /* Enable Interrupt on change of link status */
#define PHY_LINK_STATUS      ((uint16_t)0x2000) /* PHY link status interrupt mask */

    /* Note : Common PHY registers are defined in stm32f4x7_eth.h file */

    /* Exported macro ------------------------------------------------------------*/
    /* Exported functions ------------------------------------------------------- */

#ifdef __cplusplus
}
#endif

#endif /* __STM32F4x7_ETH_CONF_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/